Compact RESISTANT anti-vandalism keypad

Anti-vandal keypad with integrated proximity, narrow profile and small dimensions. It allows working in autonomous or centralized mode. With a maximum capacity of up to 600 users, if a user capacity between 600-1000 is needed, it is possible to configure the keyboard as wiegand26 and connect it to an autonomous MINI controller ref. 5276. To access the user database on a PC or allow access to more than 600 people, this keyboard can be configured in Wiegand 26/8bits burst so that it can be installed in a centralized system such as AC-MAX, AC+ o IP-AXES, which will allow you to have a record of inputs and outputs knowing the time, user and access. To carry out this type of installation, it is necessary to add an external controller to the reader, which will be managed by a PC and will be able to have the user database and view the event log in real time or offline.

It has of:
- 2A relay output configurable from 1-99sg (5sg by default) or bistable (when presenting the card the relay is activated and when presenting it again, it is deactivated).
- Door sensor input open.
- Exit button input.
- Alarm output- (negative output that allows activating a relay ref.2013).

This keypad allows up to 4 different types of access:
- Card only
- Card+PIN.
- Card or PIN (default)
- Multi-card, PIN: When presenting 2 to 9 valid cards or pins, the door will open. Entering the access code is done by entering the 4 to 6 digit code + #. Multicard/PIN type access allows the user to always be accompanied. For example, if it is programmed with 3 identifiers, in order to activate the door, the user will be there with his valid card and until the two additional cards pass (example of the guards), the door will not open. Each user is associated with an identifier number called ID (1-600). Users with ID (1-598) are standard users who upon presentation of a valid card or code will open the door. Users with ID (599 or 600) are panic users. When presenting their card or valid code, these users open the door and simultaneously activate the auxiliary output Alarm- for 1 minute or until a valid card or pin is presented.

The keypad has a door sensor input (can be enabled or disabled). If it is activated and the door is opened without prior authorization, an alarm will go off until a valid identifier is presented and the door is closed. It will also activate an alarm, if the door is left open for more than 1 minute, after a valid access.
The keyboard is supplied with two master cards that allow you to register or cancel cards or key rings, not codes. The codes are registered through the keyboard itself.

Mechanical characteristics of the compact RESISTANT anti-vandal keypad:
- 3 mm aluminum Surface fixing system.
- Concealed screws. IP66 DIMENSIONS
- Surface mounting (55(H) x 147(V) x 20(P) mm.

Technical characteristics of the compact RESISTANT anti-vandal keypad:
- Power supply: 12-28 Vca/cc Centralized: 12Vdc
- Standby consumption: 12Vdc / 65mA
- Operating temperature: [-20ºC, +60ºC] Humidity: [10%, 90%]
- Compatibility: Cards/keyrings EM(125KHz), MIFARE (13.56MHz) and HID (ISOProxII, 125KHz)
- Configurable in Wiegand 26 proximity protocol and 8-bit burst keyboard format Relay (stand-alone) 2A (C, No, Nc)
- RF radiated power: 125KHz: 4.382dBuA/m, 13.56MHz: 2.02dBuA/m.

Technical specifications autonomous wiring of compact RESISTANT anti-vandal keypad:
- With integrated controller) ~ (Red ): 12~28Vca/dc supply positive ~- (Grey&,black): 12~28Vca/dc supply negative C (White&,black),NO (Blue),NC (Green&,black): Potential-free relay . C_common, NO_Normally open, NC_Normally closed. GND (Black), SP (Brown): door sensor GND (Black), BS (Yellow): hall exit button Alarm- (Grey), ~(Red): alarm output <,200mA

Centralized wiring of the compact RESISTANT anti-vandal keypad:
- (Red): 12Vdc supply positive - (Black): 12Vdc supply negative DT (D0) (Green), CK (D1) (White): Wiegand26 G connection (LED) (Brown): LED control. Buzz (Beep) (Yellow): acoustic signal.